Window Scrapers, Snap In, for 1 Piece Window, Beetle 65-76

OVERVIEW

Upgrade your air-cooled classic with the ultimate sealing solution for your custom 1-piece window conversion. For decades, VW enthusiasts have struggled with the traditional glue-in scrapers that often come with 1-piece window kits. Those old-school glue-in versions are notorious for peeling away in the summer heat or creating a messy, unprofessional finish that detracts from your Beetle''s aesthetics. This EMPI Snap-In Window Scraper Kit eliminates those headaches by utilizing a mechanical fastening system. Designed specifically for 1965 through 1976 Beetles that have been converted to the sleek, vent-wingless look, these scrapers provide a factory-style fit and finish that ensures your glass stays snug, quiet, and properly aligned throughout its travel.

Protection from the elements is paramount when it comes to preserving the integrity of your Volkswagen''s doors. Without high-quality scrapers, rainwater and debris can easily bypass the glass and settle in the bottom of the door shell, leading to the dreaded "VW rot" that destroys door bottoms and window regulators. These EMPI snap-in scrapers feature a high-grade rubber compound and a smooth felt lining that protects your glass from scratches while creating a tight barrier against moisture. Whether you are finishing a high-end restoration or simply tired of the wind noise and rattling associated with worn-out seals, this kit provides the robust, long-lasting performance required to keep your interior dry and your driving experience refined.

FITMENT

• Volkswagen Beetle (Sedan): 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976
• Volkswagen Beetle (Convertible): 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976
• Note: Specifically designed for vehicles equipped with 1-piece window glass conversions (removes the vent wing window).

SPECS

• Brand: EMPI
• Part Number: 00-9773-0
• Attachment Style: Snap-In (Mechanical Clip Design)
• Material: Weather-resistant EPDM rubber with protective felt/flock lining
• Inclusions: Complete 4-piece set (Inner and Outer scrapers for both Driver and Passenger sides)
• Compatibility: Compatible with most aftermarket 1-piece window glass kits
• Finish: OEM-style matte black

PRO TIPS

Tip 1: Surface Preparation is Critical. Before attempting to snap these scrapers into place, ensure the metal flange on your door is completely free of old adhesive, rust, or debris. Since many 1-piece window conversions previously used glue-in scrapers, you may need to use a specialized adhesive remover or a fine wire brush to clean the channel. A clean, smooth flange allows the snap-in clips to seat fully, preventing the scraper from "waving" or popping out when the window is rolled up and down.

Tip 2: Align Your Glass Before Final Installation. 1-piece windows are notoriously finicky regarding alignment because they lack the vertical support of the original vent wing post. Before you fully snap the scrapers home, test the window''s travel. If the glass is leaning too far inward or outward, it will put excessive pressure on the new scrapers, causing them to wear prematurely or bind the window regulator. Adjust your window stops and felt channels first, then install the scrapers to ensure a perfect, low-friction seal.

Tip 3: Use a Plastic Trim Tool for Pressure. To avoid denting the decorative trim or scratching your fresh paint, never use a metal screwdriver to force the clips into the door. Instead, use a wide, flat plastic trim tool or a rubber mallet with a clean rag. Apply firm, even pressure directly over the clip locations. You should hear a distinct "click" when the scraper is properly seated. If the scraper feels loose, check that the door flange hasn''t been pinched or widened during previous repairs, as it may need to be slightly narrowed with pliers to ensure a tight grip.