Rear Bumper Mount, Right Side, for Beetle 68-73

OVERVIEW

Restoring the structural integrity of your classic Volkswagen is paramount, especially when dealing with the rear quarter section where road debris and moisture tend to congregate. This KeyParts Rear Bumper Mount for the right (passenger) side is a precision-engineered replacement component designed specifically for the 1968 through 1973 Standard Beetle. Over decades of service, the original bumper mounts often fall victim to "tin worm" rust or succumb to the stresses of minor rear-end collisions, leaving your Europa-style bumpers sagging or improperly aligned. This heavy-gauge steel mount provides the factory-correct foundation needed to secure your rear bumper brackets, ensuring that your Beetle''s silhouette remains sharp and its safety components are firmly anchored to the chassis. Whether you are performing a concours-level restoration or simply patching up a reliable daily driver, this mount is the professional''s choice for a permanent, metal-finished repair.

Installation of this component requires a commitment to quality bodywork, as it is a weld-on piece that replaces the often-deteriorated original sheet metal. While it is designed as a direct fit for the 1968-1973 models, seasoned air-cooled builders frequently utilize this mount for custom applications or to adapt earlier 1949-1967 Type 1 chassis for different bumper configurations, thanks to its robust stamping and adaptable flange area. The mount arrives in a protective coating to prevent flash rust during transit, providing a clean surface for your welding prep. By choosing this KeyParts mount from Appletree Automotive, you are investing in a part that respects the original engineering of the Beetle while providing the durability required for another fifty years on the road. Don''t settle for flimsy universal brackets when you can install a structural component that matches the thickness and contour of the German original.

FITMENT

• Volkswagen Standard Beetle (Type 1): 1968, 1969, 1970, 1971, 1972, 1973
• Volkswagen Super Beetle (Type 1): 1971, 1972, 1973
• Custom Applications: Can be adapted for pre-1968 Beetle models with appropriate metal fabrication and welding.

SPECS

• Part Number: 111-809-636F
• Position: Rear, Right Side (Passenger Side)
• Material: Heavy-duty stamped steel
• Installation Method: Weld-on (requires removal of old damaged metal)
• Compatibility: Designed for Europa-style bumper brackets
• Weight: 1.2 lbs
• Finish: Weldable storage primer
• Application: Structural bumper support and quarter panel reinforcement

PRO TIPS

1. Prioritize Perfect Alignment Before Tacking

One of the most common mistakes during a rear-end restoration is welding the bumper mount in place without verifying the bumper''s final position. Before you lay down your final beads, we strongly recommend "mocking up" the entire assembly. Bolt your bumper bracket to this new mount and attach the actual bumper blade. This allows you to check the horizontal level and the distance from the bodywork on both the left and right sides. It is much easier to adjust the mount''s position while it is held by Clecos or a few small tack welds than it is to grind off a fully finished weld because the bumper is sitting crooked.

2. Master the Weld-Through Primer Technique

Since this mount is welded directly to the body, the back side of the metal (the side facing the interior of the quarter panel) becomes a prime candidate for hidden rust because you cannot reach it with paint after it is installed. Before welding, grind the mating surfaces to bare metal and apply a high-quality zinc-based weld-through primer. This specialized coating protects the steel from oxidation caused by the heat of the welding process and provides a layer of corrosion resistance in the "sandwich" area between the new mount and the original body metal where traditional paint can''t reach.

3. Seal the Seams for Longevity

Once the welding is complete and the welds have been ground smooth, don''t rely on paint alone to keep the moisture out. The rear bumper area of a Beetle is constantly bombarded by water and road salt kicked up by the rear tires. Use a professional-grade automotive seam sealer along all the edges of the new mount. This prevents capillary action from drawing moisture into the microscopic gaps between the metal panels. Follow up with a high-build primer and a quality undercoating or chassis paint to ensure that your repair remains rust-free for the life of the vehicle.