Round Spring Plate Grommets, 1-7/8 ID, Bugpack, Pair

OVERVIEW

Elevate your air-cooled Volkswagen''s rear suspension performance and structural integrity with these premium BUGPACK Round Spring Plate Grommets. Standard factory rubber bushings are notorious for degrading over time, leading to excessive "squish," unwanted camber changes, and a "mushy" feel in the rear end that compromises both safety and handling. These high-density polyurethane grommets are specifically engineered to eliminate the "crunching" and bottoming out that occurs when stock rubber reaches its compression limit. By providing a significantly more stable pivot point for your spring plates, these grommets ensure that your suspension geometry remains consistent even under heavy load, delivering sharper handling and a more predictable ride whether you''re cruising the boulevard or tackling off-road trails in a sand rail.

Sold as a matched pair, these 1-7/8 inch ID grommets are an essential upgrade for any restorer or performance enthusiast looking to tighten up their chassis. Unlike standard rubber, the advanced polyurethane material used by Bugpack is highly resistant to oil, grease, road salt, and environmental contaminants that typically rot factory components. This means once they are installed, they are designed to outlast the vehicle itself. Whether you are maintaining a vintage 1950s Beetle or upgrading a late-model Type 3, these grommets offer the perfect balance of firmness and vibration dampening. They ensure your torsion bars can operate through their full range of motion without the interference of sloppy, worn-out mounting points, providing that "like-new" feel every VW owner craves.

FITMENT

• VW Beetle Type 1: 1950-1960 (INNER Position)
• VW Beetle Type 1: 1969-1979 (OUTER Position)
• VW Type 3 (Squareback, Fastback, Notchback): 1969-1979 (OUTER Position)
• VW Ghia: Fits corresponding years/positions as Type 1
• Custom Applications: Fits many Sand Rails, Dune Buggies, and Manx-style shells utilizing 1-7/8 inch torsion housings.

SPECS

• Brand: BUGPACK
• Part Number: B658812
• Inner Diameter: 1.875 Inches (1-7/8")
• Outer Diameter: Large Format (designed for standard round torsion covers)
• Material: High-Performance Polyurethane
• Quantity: Sold as a Pair (2 pieces)
• Color: Signature Bugpack Red
• Configuration: Round Inner/Outer Spring Plate Grommet

PRO TIPS

Pro Tip 1: Silence the Squeak with Proper Lubrication. Polyurethane is much stiffer than rubber, which is great for performance, but it can lead to annoying "squeaking" if installed dry. Always apply a generous coating of high-quality silicone-based grease or "moly-lube" to both the inner and outer surfaces of the grommet where they contact the spring plate and the torsion housing. Avoid using petroleum-based grease, as it can eventually break down certain synthetic materials. Proper lubrication ensures a silent, smooth-acting suspension for years to come.

Pro Tip 2: Prepare the Housing Surface. Before installing your new Bugpack grommets, take the time to thoroughly clean the inside of the torsion housing and the spring plate neck. Over decades, rust scales and old rubber residue can build up, creating an uneven surface that prevents the new grommet from seating perfectly. Use a wire brush or a flap wheel to bring the metal back to a smooth finish. This ensures the 1-7/8" ID fits snugly and prevents the grommet from "walking" or shifting during hard cornering.

Pro Tip 3: Inspect Your Torsion Bar Splines. While you have the spring plates removed to replace the grommets, it is the absolute best time to inspect your torsion bars for signs of fatigue or hairline cracks. Clean the splines on both the torsion bar and the spring plate, and apply a light coat of anti-seize before reassembly. This makes future ride-height adjustments much easier and prevents the torsion bar from becoming "welded" to the spring plate due to corrosion. Remember to mark your spring plate position before removal if you don''t intend to change your current ride height!